time and motion study

Maintenance Management Resources
Six sigma and lean manufacturing, it's all about money:
Business Industrial Network is your best resource when you need fast solutions. After you view this six sigma area dedicated to learning the true cost of equipment downtime with time and motion study, please visit our company.


True Cost of downtime
Spacer Spacer

Definition of Root Cause Analysis (RCA)

 Add to favorites
One of the lean manufacturing principles explained in this refreshing article. feedforward first page

From the newsletter "Process Plant and Equipment UP-TIME" by www.trade-school.education – Leaders in Plant Maintenance Continuous Improvement

Article sponsored by ... IDCON's Root Cause Analysis Training and Consulting

What you will learn from this article.

  • An explanation of root causes analysis (RCA).

  • An overview of how it is applied at your work place.

  • See the result of a sample RCA.

ABSTRACT - Root cause analysis answers your problem. Root Cause Analysis (RCA) is a step by step method that leads to the discovery of a fault's first or root cause. Every equipment failure happens for a number of reasons. There is a definite progression of actions and consequences that lead to a failure. An RCA investigation traces the cause and effect trail from the end failure back to the root cause. Much like a detective solving a crime. Keywords: failure mode, fault finding, fault tree, cause tree, events.


The method brings a team of 3 to 6 knowledgeable people together to investigate the failure using evidence left behind from the fault. The team brainstorms to find as many causes of the fault as possible. By using what evidence remained after the fault, and through discussions with people involved in the incident, all the non-contributing causes are removed and the contributing causes retained.

A fault tree is constructed starting with the final failure and progressively tracing each cause that led to the previous cause. This continues till the trail can be traced back no further. Each result of a cause must clearly flow from its predecessor (the one before it). If it is clear that a step is missing between causes it is added in and evidence looked for to support its presence.

Once the fault tree is completed and checked for logical flow the team then determines what changes to make to prevent the sequence of causes and consequences from again occurring.


It is not necessary to prevent the first, or root cause, from happening. It is merely necessary to break the chain of events at any point and the final failure cannot occur. Often the fault tree leads to an initial design problem. In such a case redesign is necessary. Where the fault tree leads back to a failure of procedures it is necessary to either address the procedural weakness or to install a method to protect against the damage caused by the procedural failure. Below is a sample fault tree for the moral story of the kingdom lost because of a missing horseshoe nail.


The story is told that before an important battle a king sent his horse with a groomsman to the blacksmith for shoeing. But the blacksmith had used all the nails shoeing the knight's horses for battle and was one short. The groomsman tells the blacksmith to do as good a job as he can. But the blacksmith warns him that the missing nail may allow the shoe to come off. The king rides into battle not knowing of the missing horseshoe nail. In the midst of the battle he rides toward the enemy. As he approaches them the horseshoe comes off the horse's hoof causing it to stumble and the king falls to the ground. The enemy is quickly onto him and kills him. The king's troops see the death, give up the fight and retreat. The enemy surges onto the city and captures the kingdom. The kingdom is lost because of a missing horseshoe nail.

The cause tree explains step-by-step how the events leading to the king's death unfolded. Notice that two separate event 'branches' had to occur together for the sequence to continue to the fateful end. If any of the causes could have been prevented then the kingdom would have been safe.

Root Cause Analysis

A special thanks to Mike Sondalini - Equipment Longevity Engineer

and www.trade-school.education  for donating this article to our visitors.

fault tree analysis small

Fault Tree Analysis e-Book
(We highly recommend you download this related ebook today.)

Another method of analysis is Design of Experiment (DOE)

See Also: SolidCount™, an advanced production counting tool.






New Document

Corporate Sponsors

Supporting the True Cost of Downtime with their product and services

PLC Training

PLC training


Automation training 



Spacer Spacer
MAIN:  Home | TDC | Standards | OEE | Glossary | Download | Search | Feedback
TDC:  Equipment | Labor | Downtime | Link to us | Site Content Page | Awards
Other:  Contact Us | About DT
Entire Site Map